ASTM A517 Grade B Quenched and Tempered Alloy Steel Plate for Boilers and Other Pressure Vessels

• After-sales Service: Technical/Sample/Quality
• Warranty: Technical/Sample/Quality
• Type: Steel Plate
• Standard: ASTM
• Certification: ISO
• Technique: Hot Rolled
• Model NO.: ASTM A517 Grade B
• Application: Boiler Plate
• Stock: Stock
• Grade: ASTM A517 Grade B
• Transport Package: Steel Strip
• Specification: 3-20mm
• Trademark: SHUNFU
• Origin: China
• Production Capacity: 100000 Tons Per Year

Product Description

ASTM A517 Grade B quenched and tempered alloy steel plate for boilers and other pressure vessels
 

General Product Description

ASTM A517 Grade B is a quenched and tempered alloy steel plate intended for use in fusion welded boilers and other pressure vessels. A517 Grade B has a minimum yield strength of 100 ksi [690 MPa] and a minimum transverse Charpy V-notch lateral expansion of 0.015 inches (0.38 mm).
Applications
Typical applications for A517 Grade B include unfired pressure vessels and tanks.

Dimension Range

GRADE	PRODUCT TYPE	THICKNESS (in)	WIDTH (in)	LENGTH (in)
B	Mill plate	0.188 - 1.250	72 - 120	240 - 588

Width: Inquire for widths less than 72 inches and greater than 120 inches.
Length: Inquire for lengths less than 120 inches and greater than 588 inches up to 600 inches.
 

Mechanical Properties

Tensile testing is performed in the transverse direction according to ASTM A20 requirements. The tensile property requirements are tabulated below:

GRADE	THICKNESS (in)	0.2% YS (ksi)	UTS (ksi)	ELONGATION IN 2" 1) (MIN %)	REDUCTION IN AREA FOR RECTANGLE SPECIMENS 2) (MIN %)	REDUCTION IN AREA FOR ROUND SPECIMENS 3) (MIN %)
B	0.188 - 1.250	100	115 - 135	16	35	45

1) Refer to ASTM A20/A20M for Elongation adjustments based on plate thickness.
2) Reduction in area for 1.5 inches wide rectangular tension specimen. For plate thicknesses of 0.750 inches and less, the test specimen must be a 1.5 inch wide rectangular specimen.
3) Reduction in area for 0.5 inch wide round tension specimen.

Mechanical Testing

Charpy V-Notch Impact Properties: A transverse Charpy V-notch lateral expansion of 0.015 inches [0.38 mm] in individual specimens can be guaranteed to a minimum test temperature of -40°F [-40°C]. Please inquire for applications requiring lower test temperature guarantees for 0.015 inches [0.38 mm] minimum transverse lateral expansion and for other specified minimum impact property requirements. All test temperatures must be specified on each purchase order.
 

Chemical Composition (ladle analysis)

Meets chemical requirements of ASTM A517 Grade B (Ladle Analysis, wt. %, maximum noted unless indicated by acceptable range):

C (%)	MN (%)	P (%)	S (%)	SI (%)	CR (%)	MO (%)	V (%)	TI (%)	B (%)
0.15 - 0.21	0.70 - 1.00	0.025	0.008 1)	0.15 - 0.35	0.40 - 0.65	0.15 - 0.25	0.03 - 0.08	0.01 - 0.04	0.0005 - 0.005

1) Note that SSAB's S level is more restrictive than ASTM specification requirements for A517 Grade B.

Carbon Equivalent

THICKNESS (in)	0.188 - 1.250
Typical CET (wt %)	0.34
Typical CEV (wt %)	0.51

 

Tolerances

Thickness, width, and length tolerances for A517 Grade B steel plate are in accordance with the requirements of ASTM A20. The flatness tolerance for as- supplied product is ½ ASTM A20.
 

Delivery Conditions

ASTM A517 Grade B is supplied in the quenched and tempered condition.
 

Weldability

Welding of A517 Grade B shall be performed in accordance with the applicable welding code. Special welding consumables and welding procedures may be needed to meet specific requirements for a given application. Low hydrogen practices are strongly recommended, including the removal of surface moisture. A517 Grade B may be susceptible to reheat cracking in the heat-affected zone of welds during stress relieving or postweld heat treatment. As a result, SHUNFU recommends that a qualified welding engineer consider this potential before stress relieving weldments of this product. For additional welding information, please contact your SHUNFU representative.